Home Page

Skate Sharpening & Fitting by APPOINTMENT only.

Please call ahead to set APPOINTMENT.

(734) 525-1704

Contact Us Today 734-525-1704 or email This email address is being protected from spambots. You need JavaScript enabled to view it.

Skate Sharpening & Skate Fitting By APPOINTMENT only!
Please call ahead to set an APPOINTMENT.

edea logoEdea - Preferred Boots of Olympic, world & international skaters.

Mike recently attended a workshop training seminar to further his experience in fitting and shaping this remarkable product. This was held in Richmond Indiana, headquarter for 'Skates USA,' the US Distributor for Edea Boots.

Podium Skates now has several models in stock to try on and experience the comfort, strength and durability of this remarkable product.


  • jacksonJackson-Stock and Custom Boots



MKBrand: MK

Models: Goldstar, Vision, Vision Synchro, Phantom, Dance, and all other models

john wilsonBrand: Wilson

Models: Coronation ACE, Pattern 99, Pattern 99 Parabolic, Gold Seal, Gold Seal Parabolic, and all other models

New Model: The 'Phoenix' by John Wilson Blades. 🔥 46% lighter than traditional blades, with a full carbon fibre body and stainless steel runner - it's the lightest blade ever made. Coming soon. Available in silver or black.

paramountBrand: Paramount

Models: All Models

jacksonBrand: Jackson Ultima & Matrix

Models: Mirage, Aspire, Aspire XP, Legacy, Elite, Freestyle, Supreme

Models: Legacy (including colors), Elite (including colors), Freestyle, Supreme, and all other models also available


Blade Mounting

blades 1When the boots have been leveled and sealed, it is time to attach the blades to them. As long as the skater has been correctly aligned in the boot, meaning proper arch support has been achieved, the blades may be placed in a centered, neutral position. The skate technician needs to evaluate the whole bottom of the boot, as the skaters feet extend beyond the width of the boot sole.

Once the desired position is determined, the blades are attached with stainless steel screws. Most of the screws supplied with blades are not ideal to use in the mounting process. Some are merely zinc plated, fine for many tasks, but not for the constant exposure to moisture they will encounter. Others have heads that strip out easily, making removal difficult or impossible. Special stainless steel screws are purchased and used at Podium Skates to ensure a lasting secure blade mount. Silicone caulk is applied over all holes before screws are inserted, so water cannot seep in and cause the leather to rot and the screws to loosen. Only enough screws to hold the blade securely for trial are used initially. More are added when the skater is sure the blades are properly aligned for their optimal performance.

  • Policy on Blade Mounting

Because all elements of a boot fitting and blade mounting are intertwined and success at one procedure depends on the other steps before it, we do not mount blades on boots purchased over the internet, by mail, or directly from the manufacturer. We will be happy to mount your used blades to a new boot fit and prepared by us, so long as the size is right and there is sufficient skating life left in the blades.

Your skates can be made to look like no one elses. Stickers, designs, and glitter, in many colors, can be applied during the urethane sealing process.

Five to six coats of urethane are first applied. The soles and heels are then decorated, according to the skater's wishes. Thousands of stickers are on hand to choose from and at least 50 shades of glitter. The possible combinations are endless; no one personalizes skates like we do at Podium. The skater's name is also inscribed on the sole or heel under the urethane layers, making your skates truly one-of-a-kind!

Proper fitting skate boots are critical to the performance and well being of a skater. They must be of adequate strength to support the difficult moves and jumps a skater attempts. At the same time, they must flex to allow the skater to bend at the knee, in order to control the edges and launch those jumps. A snug secure fit is required with the heel locked down and supported and the rest of the foot equally secure and in proper position. Toes should have some wiggle room vertically, but no excess horizontal space should exist on a correctly fit pair of boots.

  • Boot Fitting

Every skaters feet are traced, and careful measurements are taken standing and seated to determine the perfect length and width of skating boots. Many boots are stocked at Podium Skates, ready to try on, and many others can be ordered in a week or less. Fittings are not rushed; great care is taken to determine the correct size and model to provide the right amount of support and comfort for the competitive skater.

Custom boots require even more measurements, often along with foam casts of the feet and photographs, so the correct fit can be obtained.

  • Custom Insoles

Insoles made individually to the skaters feet provide perfect arch support for figure skaters. These prevent over pronation, and balance the skater correctly over the center of the blade. Usually blades can be center mounted with this method, which is better for the skater and the boots and blades. Twisting of the boots is therefore eliminated, and stress is taken off the joints of the skater as well. Changing edges, level spinning, and jump takeoffs and landings are all enhanced by this custom support. Insoles are also available for off ice training and casual shoes, and can make life much more comfortable for the skater, and the skater's parents! Mike has more experience crafting these custom insoles than any other skate technician.

  • Boot Leveling (Preparation for Blade Mounting)

Before blades are attached to the skate boot, the soles and heels need to be leveled in order for a flush fit between boot and blade. In a perfect world, blades would lay smoothly up against the boot bottoms, but in reality, this is seldom the case. At Podium Skates, boots are always prepped to accommodate the blade model being installed.

Preparation of the sole of the boot is always necessary to achieve proper mounting of the blades. Just tightening the screws in an attempt to draw the soles and heels down, to meet the blades, can put tremendous stress on both the boots and the blades. This can, and does, result in blade warpage and boot twisting, along with premature boot breakdown. When gaps exist at the heel between the boot and blade, simply landing a jump can cause the screws to snap, resulting in the blade separating from the heel, and possibly severe injury to the skater.

One method of mounting blades onto boots, is to place shims of leather or plastic into the gaps that exist between the boot and blade. We are convinced this is far from the ideal solution. Shims can become loose and fall out, or actually compress into the leather of the boot and lose effectiveness. This method does nothing to add to the stability of and integrity of the boot and blade combination.

Mike, skate technician of Podium Skates, firmly believes the most effective and safe way to prepare a boot for blade mounting, is to sand the sole and heel so there is a perfect interface between boot and blade. When a boot is sanded properly, there is nothing to loosen or change as the skate is used, or in some cases, abused.

Sanding is an art not easily mastered, one reason so few skate technicians attempt it. Sand a boot improperly, and the boot can be ruined beyond repair. When boots are leveled by sanding correctly, the blades lay flush without significant gaps on the soles and heels, and the blade is square with the vertical dimensions of the boot. The whole skate structure is improved by this method of preparation.

  • Sealing

After the boots are prepared for mounting, the next step is to seal them against moisture. A boot not properly sealed deteriorates very quickly indeed. There are several methods of sealing boots, some far more effective than others.

Beeswax or “Sno Seal” as it is commonly called, gives protection by applying multiple coats of wax to leather that has been warmed by a hairdryer, heat gun, or other method. The boots are allowed to cool in between applications.

The uppers of the boots should be taped, in order to prevent heat damage and discoloration from wax that may come in contact with it. Sno Seal is fairly effective when properly applied, although moisture eventually invades the soles after extended skating. You may notice the boots feel heavier after using them for a long time. The leather can eventually blacken from water damage, especially in the front of the sole around the blade.

Heel and sole enamel looks nice when first applied. It is not long before it starts to crack and peel or wear off. Varnishes or urethanes available at the local hardware store, unfortunately fair no better. These leave the boots vulnerable to moisture damage very quickly.

Some manufacturers ship boots with a seal already on the soles and heels. Those seals do not give adequate protection to the boots and unfortunately many cannot be improved by the further efforts of the skate technician or the consumer.

Podium Skates offers a special industrial grade urethane seal. Ten to twelve coats are applied over the course of several days. This can only be done over raw leather, in order for proper adhesion. Some manufacturers will ship their product without any seal applied to it; at least one will sand their seal off the boots before shipping. If there is any factory seal on the boots, it is impossible to successfully apply the industrial urethane to them. Boots that are properly sealed with this method do not deteriorate. The blades do not sink into the bottoms of the soles and heels, and the leather does not turn black from damage.

Skate Sharpening

  • All models of blades are expertly sharpened.

  • Custom depths of hollow are calculated for each skater or choose your own preference.

  • Edges are always square and level when finished, making sure the hollow is perfectly centered.

  • Fine grit sharpening wheels are nearly always used. These provide the smoothest edges and result in the minimum material being removed to restore edge keenness.

  • Some stainless steel blades require a medium grit wheel to obtain a proper sharpening. When this is true, those wheels are dressed very smoothly to provide the same kind of fast, clean edges.

  • Flat Bottom Groove Sharpenings

Sid Broadbent has designed and patented a revolutionary method for preparing wheels to accurately deliver this precise sharpening. Mike has more experience with this system than any other skate technician. This type of sharpening can provide the skater with considerably more speed and flow than a conventional sharpening, while still providing the edge grip a serious skater requires.

   skateart17    skateart18

   skateart19    skateart20

Share Podium Skates With Your Friends


Guests Online

We have 41 guests and no members online

Business Hours

Podium Skates

We are here to serve you during the following business hours:

Monday Closed
Tuesday 11am to 4pm
11am to 4pm
Thursday 11am to 4pm
Friday 11am to 4pm
Saturday Closed
Sunday Closed

Appointments are available outside these hours and days.

Phone: (734) 525-1704Contact Us Today

Podium Skates Menu